UPT210 Multifunction energy meter connectable to MFC150 Rogowski coil

UPT210 Multifunction energy meter connectable to MFC150 Rogowski coil

Reference: UPT210 - Manufacturer: Algodue

Compact 6 DIN modules size
High contrast LCD display
True RMS measurement
Active, reactive and apparent energy (4 counters)
Neutral current measurement
More than 35 electrical parameters measured and displayed (ENH version)
Power and current demand calculation
RS485 communication port
Programmable transformer ratios
Two digital outputs for energy pulsing
Indication of phase sequence and wrong CT connection
Up to 1% accuracy

Overview
Specifications

Switchboards, gensets, motor control centers, etc.
Replacement of electromechanical meters for household, industrial and commercial applications
Power monitoring & control systems
Individual machine load monitoring
Capacitor bank operation supervision
Remote metering and cost allocation

Measurements

Single phase and three-phase 3-wire or 4-wire unbalanced load operation.
True RMS metering provides accurate measurement even for distorted waveform.
More than 35 electrical parameters are measured. The basic version displays on the LCD the system values for a quick and easy check of the load conditions. The table on the right shows the measured parameters and the available options.
Programmable 1A / 5A current full scale allows to fit the standard CTs.
CT primary value is programmable up to 9999 to show the real energy consumption values

Front panel display

High contrast LCD display.
Two keys ensure the selection of the information on the LCD display and the instrument programming.
Password protected setup and resetting operations.

Communication

RS485 optoisolated communication port (option).
Selectable MODBUS or A2 ASCII protocol. LONBUS protocol on request.
Communication speed programmable up to 57600 bps (78 kbps in case of LONBUS).

Inputs & outputs

Two digital optoisolated outputs for energy pulsing. The pulse value is programmable.
On request input for Rogowski coils.

Advanced diagnostic functions

Wrong current transformer polarity and phase sequence connection errors are indicated on the LCD display.
Over / undervoltage, overcurrent and frequency out of range are detected to indicate the uncorrect working conditions.
Pulse emission frequency too high or CT too high are checked to indicate programming mistakes.

Power supply (1)
Rated voltage: powered from measuring inputs
Consumption: 0.8 VA max

Voltage inputs
Rated voltage: A) 3x230/400 VAC +15% -20% - 4 wires
B) 3x120/208 VAC +15% -20% - 4 wires
C) 3x400 VAC +15% -20% - 3 wires
D) 3x208÷230 VAC +15% -20% - 3 wires
E) 3x100÷120 VAC +15% -20% - 3 wires
Input impedance: ›1,3 MOhm
Burden: max 0,15 VA per phase
Frequency: 45 - 65 Hz

Current inputs
Rated current (Ib): 1 / 5 ARMS programmable
Min / max measurable current: 20 mA / 7 ARMS
Maximum overload: 10 ARMS continuous - 100 ARMS for 1 sec.
Input impedance: 0,02 Ohm approximately
Burden: max 0,5 VA per phase
Insulation voltage: 480 VAC max between phases
Rogowski input: 200÷49995 A on request

Typical accuracy
Voltage: ±0.3% reading ±0.05% full scale
Current: ±0.5% reading ±0.05% full scale
Active power: ±1% reading ±0.1% full scale (PF=1)
Power factor: ) 1.5% reading (0.5 inductive - 0.8 capacitive)
Active energy: 1% reading (0.5 inductive - 0.8 capacitive)
Frequency: ±0.05% reading ±2 digits from 45 to 65 Hz

Display and operating controls
Display: high contrast LCD display 43x19 mm
8 digits for energies and other parameters + symbols
Keypad: 2 push-buttons

Communication port (2)
Type: RS485 on request, optoisolated
Baud rate: 300 to 57600 bps
78 kbps in case of LONBUS
Protocols: A2 ASCII, MODBUS
LONBUS on request

Digital outputs
Type: 2 NPN or PNP optoisolated
(10÷50V-100mAAC-DC or 5÷50V-100mAAC-DC)

Environmental conditions
Operating temperature: from -15°C to +60°C
Storage temperature: from -25°C to +75°C
Relative humidity: 80% max. without condensation

Mechanical characteristics
Material: plastic enclosure - noryl UL94-V0
Protection degree: IP51 (front panel); IP20 (terminals)
Terminals: conductors 2,5 mm2
Size / weight: 106x90x57 mm, 6 DIN rail modules / 300gr

Standards compliance
Safety: 73/23/EEC and 93/68/EEC directives, EN61010.1 safety standard
EMC: 89/366/EEC directive and following modifications 93/31/EEC and 93/68/EEC, EN50081-2, EN50082-2, EN61326/A1

(1) The basic instrument is powered from L1, L2, L3 and N (4-wire version) or L1, L2, L3 (3-wire version). The presence of only one of the three phases (4-wire version) or two phases (3-wire version) ensures the normal counting and displaying operations.
(2) The serial port is powered from L1 and N (4-wire version) or L1 and L2 (3-wire version). The communication function is ensured only if the L1 phase (or L1 and L2 for 3-wire) is present and within the specified range.

UPT210 Multifunction energy meter connectable to MFC150 Rogowski coil

Viewed products

16 other products in the same category: