View larger

2410 Analizador de Aceite en Agua

Reference: 2410

Manufacturer: Waltron

Condition: New

O Waltron 2410 Oil-in-Water Analyzer é um pacote de instrumentação de última geração desenvolvido especificamente para medir a quantidade de hidrocarbonetos em água limpa.

More info about this product.

Partilhar no Facebook
Retirar este produto da minha lista de favoritos.
Adicionar este produto à minha lista de favoritos.
Print

geral
ESPECIFICAÇOES
Data sheet

- QUALIDADE DA ÁGUA -	Óleo na Água

O 2410 tem muitos usos e se encaixa uma ampla variedade de aplicações.

O óleo em água analisador 2410 utiliza sensores ópticos para medir a luz dispersa e absorvida sobre um fluxo de amostra. Medição distingue entre gotículas de óleo e turbidez. Um microprocessador calcula a concentração de ppm de óleo com base no sinal do sensor. O óleo em água analisador 2410 mede continuamente a concentração de alarmes activos e óleo e relés como necessário.

As aplicações incluem: condensado retorna caldeira, água de processo arrefecimento, controlo de vapor de processo e de águas residuais.

CARACTERÍSTICAS E BENEFÍCIOS
• Design compacto
• Manutenção mínima exigida
• Calibra diretamente à água potável
• Operação automática
• gama análise Wide: 1-99 ppm
• Auto-diagnóstico e automático contínuo
• Compensação de turbidez
• Resposta rápida

Range		1 – 99 ppm
Accuracy		± 2 ppm
Calibration		Calibrates directly to clean water
Current Outputs		0 – 20mA, 4 – 20mA (820 max load); 0 – 5VDC, 1 – 5VDC (50kW min. load)
Alarms		Two adjustable operating delay alarms (0 – 60 sec, 10 – 240 sec); contacting rating 8A @ 240V
Power		230/115VAC or 24VAC, 50/60Hz; consumption 10VA max
CE Certification (on request)		Meets low voltage and low electromagnetic compatibility directives
Electrical Installation		EN61010-1EC664 category 11
Operating Conditions
Sample Flow		0.03 – 0.53 gal/min (0.1 – 2.0 liter/min)
Sample Temperature		33.8 – 104° F (1 – 40°C)
Ambient Temperature		33.8 – 131° F (1 – 55°C)
Pressure		1.45 – 145 psig (0.1 – 10 bar) 90% RH Max @ 131° F (55°C)
Humidity		90% RH Max @ 55°C
Mechanical
Construction		Meets IP55
Dimensions		Height=8.465” (215mm);Width=9.52” (242mm); Depth=2.874” (73mm)
Weight		4.96 lbs (2.25 kg)
Finish		Corrosion resistant

Boiler Condensate Returns:

When low pressure steam is used to preheat fuel oil, any tiny leak in the heater can allow traces of the fuel oil to contaminate the condensate. The oil returns to the boiler with the feedwater. Over time, even small amounts of oil will accumulate on heat transfer surfaces causing overheating of the boiler tubes. This results in lost efficiency and in some cases failure of boiler tubes. The oil may react with the boiler treatment chemicals to cause foaming and carryover. If leakage occurs, the Model 2410 provides warning before damage occurs.

Process Cooling Water:

When a process stream containing oil is cooled, if there is a leak in the cooler, oil can contaminate the cooling water stream. Contamination can result in both pollution of the environment and loss of product. The oil-in-water monitor lets the operator know if oil gets into the cooling water.

Process Stream Monitoring:

Edible oil processing plants may use steam to aid in the extraction of oil. Regardless of whether the condensate is recycled to the boiler or sent to waste, all traces of oil must first be removed. The Model 2410 monitors the effectiveness of the separation process.

Waste Water:

Treated wastewater from oil-handling facilities can be monitored to assure that treatment processes are effective.