HS-2000 Hydraulic Training System

HS-2000

KandH

New

The “HS-2000” is launched to offer enriched knowledge from basic oil pressure components, advanced oil-pressure loop design to PLC-based electrical control system. The trainee can prepare themselves to be a high-level automation engineer with the help of the “HS-2000” trainer system.

Add to wishlist

Category Hydraulic

It is well known that “Factory Automation” is an indispensable measure to reduce labor cost, improve production efficiency and achieve higher product quality. However, it is widely adopted by electronic, semiconductor, LCD and mechanical factories. In factory automation, oil pressuring” plays a very essential and critical role.
 



1. Improvement on trainees’ familiarization of the principles and applications of various oil pressure components.

2. Demonstration of oil-pressure loop design.

3. Training of PLC programming, including architecture, instructions and ladder diagram.

 PART I : Basic Hydraulic Components

  1. Hydraulic Pump
  2. Pressure Relief Valve
  3. Pressure Reducing Valve
  4. Pressure Losses from Hoses
  5. Flow Control Valve
  6. Line Check Valve
  7. Pilot-Operated Check Valve
  8. Directional Control Valves
  9.  Single-Acting Hydraulic Cylinder
10. Double-Acting Hydraulic Cylinder
11. Hydraulic Motor
 
 
PART II: Basic Hydraulic Control Circuits
 
  1. Pressure Regulating Circuit
  2. Safety Circuit
  3. Dual Pressure Regulating Circuit
  4. Sequence Control Circuit (1)
  5. Sequence Control Circuit (2)
  6. Pressure Counterbalancing Circuit
  7. Pressure Reducing Circuit
  8. Meter-In Flow Control Circuit
  9. Meter-Out Flow Control Circuit
10. Bleed-Off Control Circuit
11. Pressure Keeping Circuit
12. Differential Circuit
13. Synchronizing Circuit
14. Accumulator Control Circuit
15. Hydraulic Motor Control Circuit
 
 
PART III : Basic Electro-Hydraulic Control Circuits
 
  1. Series Circuit
  2. Parallel Circuit
  3. Remote Control Circuit
  4. Sequence Control Circuit (1)
  5. Sequence Control Circuit (2)
  6. Cushion Control Circuit
  7. Pressure Reducing Control Circuit
  8. Meter-In Flow Control Circuit
  9. Meter-Out Flow Control Circuit
10. Bleed-Off Control Circuit
11. Two-Speed Control Circuit
12. Differential Control Circuit
13. Synchronous Control Circuit
14. Pressure Keeping Control Circuit
15. Accumulator Control Circuit
16. Hydraulic Motor Control Circuit
17.  Pressure Switch Control Circuit
 
 
PART IV : Electro-Hydraulic Sequence Control Circuits
 
  1. One-Cycle Cylinder Reciprocation using Pushbutton and Single-Solenoid Valve
  2. One-Cycle Cylinder Reciprocation using Pushbuttons and Single-Solenoid Valve
  3. One-Cycle Cylinder Reciprocation using Limit Switch and Single-Solenoid Valve
  4. Continuous Cylinder Reciprocation using Limit Switches and Single-Solenoid Valve
  5. One-Cycle Cylinder Reciprocation using Timer and Single-Solenoid Valve
  6. Continuous Cylinder Reciprocation using Timer and Single-Solenoid Valve
  7. One-Cycle Cylinder Reciprocation using Pushbuttons and Double-Solenoid Valve
  8. One-Cycle Cylinder Reciprocation using Limit Switch and Double-Solenoid Valve
  9. Continuous Cylinder Reciprocation using Limit Switches and Double-Solenoid Valve
10. One-Cycle Cylinder Reciprocation using Timer Limit Switch and Double-Solenoid Valve
11. One-Cycle Cylinder Reciprocation using Timer Limit Switches and Double-Solenoid Valve
12. Continuous Cylinder Reciprocation using Timer Limit Switches and Double-Solenoid Valve
13. Two-Cylinder Sequencing (A+B+B-A-) using Single-Solenoid Valves
14. Two-Cylinder Sequencing (A+/    / B-) using Single-Solenoid Valves
15. Two-Cylinder Sequencing (A+B+/Timing/A-B-) using Single-Solenoid Valves
16. Two-Cylinder Sequencing (A+B+A-B-) using Double-Solenoid Valves
17. Two-Cylinder Sequencing ( A+B+/   ) using Double-Solenoid Valves
18.  Two-Cylinder Sequencing (A+B+/Timing/A-B-) using Double-Solenoid Valves

30 other products in the same category: