Catalog
Loading...
fuentes RSS
No RSS feed added
Indoor and Outdoor Sensors and Probes for: Temperature, Humidity, Speed and Wind Direction, Solar Radiation, Energy and Consumption, O2, CO, CO2, Pressure, Water and Gas Quality, VOC, etc.
Widely used in pharmaceutical company, milk product plant, clinical operation room, fermentation industry et al, where microbial contamination needs to be strictly monitored and controlled. Also it is applicable in institutes that need study of the air microbial condition.
Widely used in pharmaceutical company, milk product plant, clinical operation room, fermentation industry et al, where microbial contamination needs to be strictly monitored and controlled. Also it is applicable in institutes that need study of the air microbial condition.
Widely used in pharmaceutical company, milk product plant, clinical operation room, fermentation industry et al, where microbial contamination needs to be strictly monitored and controlled. Also it is applicable in institutes that need study of the air microbial condition.
The KSW-CO2 Carbon Dioxide detector can also measure the temperature and relative humidity of the environment.
K Type thermocouple Clamp for industrial temperature measurements
The thermographic camera AO-HT-175 allows to identify those points whose poor insulation cause heat losses.They can also be used to detect leaks in pipes, dampness, check heating systems, etc.
Moisture Meter for Sawdust, Hay and Pellets BIOMASS MOISTURE METER
SMR04-3 IP68 pH analyzer (including temperature compensation), POM housing, RS485 communication, + Built-in temperature sensor (Pt 100)(0~85℃) and CAB06 configuration cable (1.5m), built-in RS485 to USB converter.
The Dissolved Oxygen Analyzer Sensor is connected directly via RS485 communication interface, providing simple, reliable, cost- saving process data with remote monitoring, calibration, configuration and diagnostics capabilities.
Suspended Solids Density Analyzer is connected directly via RS485 communication interface, providing simple, reliable, cost- saving process data with remote monitoring, calibration, configuration and diagnostics capabilities.
The ART multiparameter water quality analyzer is designed especially for drinking and pure water monitoring such as free chlorine, pH, ORP, conductivity, turbidity, temperature... etc.The analyzer provides real-time, simple, reliable, cost-efficient measurements with remote monitoring, configuration and diagnostics capabilities.It is ideally installed in...
RST VW2100 Vibrating Wire Piezometer has been designed to be embedded in earth fills and concrete or inserted into boreholes and pipes as small as 19 mm (3/4 inch) in diameter. RST VW2100-DP Vibrating Wire Piezometer is designed to be driven into unconsolidated fine grain material such as sand, clay, or silt.
Detachable Leaf-ClipsSupplementary detachable leaf-clips for use with the FluorPenFP 110/D and the PAR-FluorPenFP 110/D.10-piece set.
- Non Contact Linear Position Sensor based on Hall Effect Tenology.- Accurate Linearity upto 1% F.S. or 0.5% F.S (on request)- Inbuild signal conditioner for 0-10Vdc output / 4-20mA output.- Extremely Long Life.- Extremely Compact in Size.- Short Circuit, Overvoltage and Reverse polarity protected.
- Speed and Direction sensor is based on magnetic Hall's effect Technology.- GTS-DO is Dual Output Magnetic Proximity sensor such that channel A lags or leads Channel B if used along with a gear wheel.
- Non Contact Rotary Position Sensor based on Hall Effect Tenology- Accurate Linearity upto 1% F.S. or 0.5% F.S (on request)- Extremely Long Life.- Extremely Compact in Size.- Angle programmable based on customer specific requirement- Short Circuit Protected. ( For 5Vdc and PWM output versions).- Overvoltage protected. ( For 5Vdc and PWM output...
- Rotary Rugged Sensor is a transducer to detect the angle / speed of the system which correspondence to the rotary motion of the shaft. - Rotary Rugged Sensor is based on contactless Magnetic technology and hence has a very long life- This Transducer can be customised in several ways to have different Electrical angle, Voltage Output, Current Output,...
The piezometer cable allows multiple piezometers to be installed simply and reliably in a single well. The piezometer string and slurry tubing are placed in the well and cement and bentonite slurry is pumped until the well is filled.
Couplers compatible with HOBO Shuttle U-DTW-1 and HOBO Base Station-U4 for data loggers:- HOBO Pendant (Model: Coupler2-A)- HOBO U20 Water Level (Model: Coupler2-B)- HOBO U22 / U24 / U26 / U20L (Model: Coupler2-C)- HOBO TidbiT v2 (Model: Coupler2-D)- HOBO U23 Pro V2 (Model: Coupler2-E)
Buying in quantity or just want some useful advice?Call +34 916292106 or complete our form More info about this product.